How To Make A Patch Cord
Jan 26, 2006 This simple, no nonsense guide, will teach you how to make a good Ethernet patch cord at a fraction of the price it would cost you to.
How to Make a Category 5 / Cat 5E Patch Cable. Did you know. Application Note: To make a crossover patch cable, you should wire one end 568B and the other end.
- Download - How to make a Cat 6 Patch Cable. Questions. Comments. Give us a shout at 866-738-8993. SIGN UP FOR SAVINGS, NEWS, UPDATES. Full Name.
- How To Make CAT5e Patch Cables Due to numerous requests for wiring diagrams or general information on how to build patch cables.
A patch cable or patch cord or patch lead is an electrical or optical cable used to connect patch-in one electronic or optical device to another for signal routing.
You ll find the newest styles for Make Patch Cord here at LightInTheBox.com, the world s leading wholesale and retail website. We provide great quality Make Patch.
This procedure generally applies to Cat 5e RJ45 connectors.
An alternate method is given for connectors utilizing a load bar.
Cut the cable to the length needed.
If you plan to use snagless boots, this would be a good time to slide them on.
Be sure the boots will be facing out towards the connector.
Strip back the cable jacket approximately 1 inch.
Use the cutter provided with the crimping tool or strip by hand.
Be careful not to nick the individual wires.
Un-twist each of the 4 pairs and straighten each wire as much as possible between the fingers.
Use the 568-B wiring scheme on both ends for a standard patch cable.
For a crossover type cable use the 568-B scheme on one end and the 568A on the other end.
Bring all of the wires together as closely as possible.
Hold the grouped and sorted wires together tightly between the thumb, and the forefinger.
Cut all of the wires at a perfect 90 degree angle from the cable,
1/2 inch from the end of the cable jacket.
Use a sharp cutting tool so as not to squash the wire ends.
With the connector pins facing up, carefully insert the wires into the connector.
Apply a moderate amount of force in order to properly seat the wires against the contacts in the connector.
Alternate for load bar Type Connectors
Note that the loadbar has slots on one side with a flanged edge on one end.
The sloted side should face the pins inside the connector.
The wires are inserted into the flanged end.
Hold the grouped and sorted wires together tightly, between the thumb, and forefinger.
Cut all of the wires at a sharp angle from the cable.
Hold the load bar so the staggered holes face toward the cable.
Insert the wires through the load bar, one at a time, carefully observing the orientation.
Slide the load bar as far down as possible.
Cut off the excess wire ends with a straight cut about 0.25 past the load bar.
With the connector pins facing up, slide the load bar assembly into the connector.
Insure that the wires are firmly seated to the end of the connector.
The brown pair wires should be on the right side.
Observe the tip of the connector to confirm that all the wires are fully inserted.
The end of each wire you should be in full view.
There should be enough of the cable jacket inside the connector to crimp against.
Tip: Slide the load bar forward as necessary to provide the ideal placement.
Place the connector into the crimp tool, and squeeze hard so that the handle reaches its full swing.
Repeat the process on the other end using the desired wiring scheme.
Be sure to slide the snagless boots snugly over the connectors when finished.
Always use a cable tester to check for continuity, opens and shorts.
Building patch cables takes practice so keep at it until you master your technique.
Download - How to make a Cat 5e Patch Cable
Give us a shout at 866-738-8993.
Knowing how to create your own Cat 5 patch cables in the length that you want can be very handy and save you money. TechRepublic has you covered.
How to make a patch cord. Jason Lee. Could United s CEO return to work after a heart transplant. iPhone 7 Dropping the Headphone Jack Signals First.
